← Product pageDownload PDFBuy Online
ZEEL PRODUCT
ZEEL PRODUCT
A-23, Reva Duplex, Behind Bharat Petrol Pump, Near Shyamal Greens, Ankhol, New Waghodia Road, Vadodara, Gujarat 390019, India
Tel: +91 97245 93964, +91 97238 59512 · [email protected]
ISO 9001:2015 · ISO 14001:2015 · ISO 22000:2018

Technical Data SheetZEELCHEM™ DF — Silicone Defoamer

Technical Data Sheet
Document no.ZP/TDS/DF/01
Revision01
Issue date12-11-2026
Product typeSilicone antifoam emulsion
AppearanceThick, milky white liquid emulsion
Ionic natureNon-ionic
pH (as such, 25 °C)6.0 – 8.0
Specific gravity (25 °C)0.98 – 1.02
Viscosity (Brookfield, 25 °C)1,500 – 4,000 cP
Non-volatile matter (105 °C)20 – 24 %

1Product description

ZEELCHEM™ DF is a high-efficiency, water-dilutable silicone defoamer based on polydimethylsiloxane (PDMS) and hydrophobic silica, supplied as a thick, milky white liquid emulsion. It gives fast foam knockdown and long-lasting foam suppression in water-based industrial systems over a wide range of temperature and pH.

Product type: Silicone antifoam emulsion (polydimethylsiloxane based) · Brand: ZEELCHEM™ · Manufacturer: ZEEL PRODUCT, Vadodara, India

2Typical properties

PropertyTypical value
AppearanceThick, milky white liquid emulsion
Chemical naturePolydimethylsiloxane emulsion with hydrophobic silica
Ionic natureNon-ionic
Active silicone content20 ± 2 % (standard grade; 10 % and 30 % grades on request)
pH (as such, 25 °C)6.0 – 8.0
Specific gravity (25 °C)0.98 – 1.02
Viscosity (Brookfield, 25 °C)1,500 – 4,000 cP
Non-volatile matter (105 °C)20 – 24 %
SolubilityDispersible in cold / room-temperature water
Flash pointNot applicable (water based)

Typical values, not a specification. Refer to the batch Certificate of Analysis.

3Features & benefits

  • Very fast foam knockdown and long persistence
  • Effective at low dosage (typically 10–200 ppm)
  • Stable over wide pH and temperature range
  • Non-ionic — compatible with most process chemicals
  • Easily diluted with water for pump or spray dosing

4Applications

  • Effluent & sewage treatment plants (ETP / STP / CETP)
  • Textile wet processing — dyeing, scouring, bleaching, washing
  • Detergent, chemical and pharmaceutical manufacturing
  • Distillery fermentation and spent-wash treatment
  • Agrochemical formulations
  • Cooling water and general industrial process water

5Recommended starting dosage

ApplicationStarting dosage
ETP / STP10 – 100 ppm on flow
Textile dyeing0.1 – 0.5 g/L of bath
Chemical / detergent processing0.01 – 0.1 % on batch
Distillery & fermentation10 – 200 ppm, on demand

Optimum dosage depends on the system and should be established by trial. Start at the lower level and increase until foam is controlled.

6Method of application

  • Stir or roll the container gently before use.
  • Use as supplied, or pre-dilute by adding the product slowly to clean cold / room-temperature water under stirring (typically 1:5 to 1:20). Use dilutions within 24 hours.
  • Dose continuously at, or just before, the point of foam generation using a metering pump, spray nozzle or batch addition.

7Packing

50 kg HDPE carboy · 200 kg HDPE drum · 1,000 kg IBC (on request).

8Storage & shelf life

Store in tightly closed original containers in a cool, shaded place between 5 °C and 35 °C. Protect from frost and direct sunlight. Shelf life: 12 months from date of manufacture in unopened packs. Stir before use.

9Handling & safety

Wear gloves and safety goggles. Spills make floors slippery — absorb with inert material and clean promptly. Refer to the Safety Data Sheet (SDS) before use.

The information in this data sheet is based on our present knowledge and is given in good faith for reference. It does not constitute a warranty or specification. Users should test the product to establish suitability for their own process. ZEELCHEM™ is a brand of ZEEL PRODUCT.
© ZEEL PRODUCT · ZEELCHEM™ — confidential reference document, reproduction prohibitedwww.zeelproduct.com/defoamer