ISO 9001 · 14001 · 22000 certified🚚 Pan-India dispatch from Vadodara
Answers

Frequently asked questions

Quick answer: Water treatment polymers like PAA, HPMA, MA/AA, AA/AMPS and terpolymers are scale inhibitors and dispersants dosed at about 2–20 mg/L. Below are clear answers on selection, dosage, safety, supply and pricing.

General

What is a scale inhibitor?

A scale inhibitor is a chemical, usually a polymer or phosphonate, that stops dissolved salts such as calcium carbonate, calcium sulphate and calcium phosphate from crystallising as hard deposits on heat-transfer surfaces, pipes and membranes. It works at very low doses (mg/L) through threshold inhibition.

What is the difference between a scale inhibitor and a dispersant?

A scale inhibitor stops dissolved salts from forming crystals. A dispersant keeps particles that are already solid (silt, iron oxide, precipitates) suspended so they do not settle. Most water treatment polymers do both, in different proportions.

Which is better, PAA or HPMA?

Neither is better in all cases. PAA (ZEELCHEM™ 1000) is the cost-effective choice for calcium carbonate scale and dispersion under normal cooling tower conditions. HPMA (ZEELCHEM™ 200) is better at high temperature, high pH and high alkalinity, as in boilers and evaporators.

Why are sulphonated polymers like AA/AMPS used?

Sulphonate groups do not precipitate with calcium, so AA/AMPS stays active in hard, high-pH water. That makes it the best polymer for calcium phosphate, zinc stabilisation and iron dispersion.

What does solid content mean on a polymer COA?

Solid content is the non-volatile part of the product after drying. It is a good indicator of active polymer, so dosage comparisons between suppliers should be made on an equal-solids basis.

Are water treatment polymers biodegradable?

Polyacrylates are not readily biodegradable, but they have low toxicity and are largely removed by adsorption on sludge in treatment plants. They contain no phosphorus, which helps meet discharge limits.

Can polymers be used with chlorine?

Yes. ZEELCHEM™ polymers are stable at the normal free-chlorine levels (0.2–1.0 mg/L) used in cooling water. Very high chlorine or bromine levels can reduce performance over time.

How are polymers dosed?

With a diaphragm dosing pump into the cooling tower basin, the make-up line or the RO feed line after the cartridge filter. Dosing should be continuous and proportional to make-up or blowdown.

What packing sizes are available?

60 kg HDPE carboys and 240 kg HDPE barrels (ZEELCHEM™ 7000 terpolymer: 65 kg carboy and 260 kg barrel).

How do I check today's price?

Each product page shows the current price when it is listed. You can also WhatsApp +91 97245 93964 or use the Buy Online button.

Do you export?

Our main market is India. For export enquiries, contact [email protected] with destination and quantity.

What payment options are available?

Online payment on our shop (www.zeelchem.online), and bank transfer or UPI for direct orders. GST invoice is provided with every order.

ZEELCHEM™ 1000 · Polyacrylic Acid

What is ZEELCHEM™ 1000 used for?

It is a low molecular weight polyacrylic acid used as a scale inhibitor and dispersant, mainly for calcium carbonate scale in cooling towers, boilers, RO antiscalant formulations, detergents and textile processing.

What is the typical dosage of polyacrylic acid in a cooling tower?

Typically 5–15 mg/L as product in the recirculating water when used alone. In a blended program with phosphonates it usually makes up 20–40 % of the formulation.

Is polyacrylic acid the same as sodium polyacrylate?

No. ZEELCHEM™ 1000 is the acid form (pH 2–3). ZEELCHEM™ 1000.S7 is the neutralised sodium salt (pH 6–8), which is easier to handle and preferred where acidity is a problem.

Can PAA be mixed with HEDP or ATMP?

Yes. PAA is fully compatible with HEDP, ATMP, PBTC, zinc salts, molybdate and azoles. These blends are the base of most cooling water programs.

Do you supply polyacrylic acid across India?

Yes. ZEEL PRODUCT dispatches from Vadodara, Gujarat to every state in India by road transport, in 60 kg HDPE carboys and 240 kg HDPE barrels.

ZEELCHEM™ 200 · Polymaleic Acid (HPMA)

What is HPMA used for?

HPMA (hydrolysed polymaleic anhydride) is a scale inhibitor mainly for high-temperature and high-alkalinity systems: boilers, thermal desalination, evaporators, oilfield water and alkaline cooling towers.

What is the difference between HPMA and polyacrylic acid?

HPMA has two carboxyl groups per unit and a very low molecular weight. That makes it stronger against scale at high temperature and pH. PAA is a better dispersant and usually cheaper for normal cooling tower conditions.

Up to what temperature is HPMA effective?

HPMA keeps its threshold inhibition up to about 300 °C, so it is used in boilers and brine heaters.

What does bromine value mean in HPMA?

Bromine value measures residual unsaturation (unreacted maleic double bonds). A low value (≤ 80 mg/g) indicates good polymerisation and stable product quality.

Is HPMA available in bulk?

Yes. ZEELCHEM™ 200 is available in 60 kg HDPE carboys and 240 kg HDPE barrels, with pan-India dispatch from Vadodara.

ZEELCHEM™ 3000 · Co-polymer of MA/AA

What is MA/AA copolymer?

It is a copolymer of maleic acid and acrylic acid used as a scale inhibitor and dispersant, especially in hard, high-alkalinity water and in detergents.

When should I use MA/AA instead of polyacrylic acid?

Choose MA/AA when the water has high hardness, high alkalinity or a high pH and you run without acid dosing. PAA can lose efficiency or precipitate with calcium in those conditions.

Can MA/AA be used in detergents?

Yes. After neutralisation to the sodium salt, MA/AA is a widely used phosphate-free co-builder that prevents encrustation and soil redeposition.

What dose of MA/AA is typical in a cooling tower?

2–15 mg/L as product, depending on hardness, alkalinity, cycles of concentration and the other components in the program.

What packing is available for ZEELCHEM™ 3000?

60 kg HDPE carboys and 240 kg HDPE barrels, supplied pan-India from Vadodara.

ZEELCHEM™ 3100 · Co-polymer of AA/AMPS

What is AA/AMPS copolymer used for?

It is used mainly to inhibit calcium phosphate scale, stabilise zinc, and disperse iron, manganese and silica in cooling water, RO and closed loops.

Why is AMPS better for calcium phosphate?

The sulphonate group of AMPS stays ionised and does not precipitate with calcium, so the polymer stays active in hard, high-pH water where phosphate scale forms.

What is the active content of ZEELCHEM™ 3100?

Typically ≥ 30 % solids. Always calculate the dose on the as-supplied product and the solids content given on the COA.

Can AA/AMPS replace phosphonates?

Not fully. AA/AMPS is a dispersant and phosphate/zinc stabiliser; phosphonates give strong CaCO₃ threshold inhibition. They work best together.

Do you supply AA/AMPS outside Gujarat?

Yes. ZEEL PRODUCT ships ZEELCHEM™ 3100 to all states of India, including Maharashtra, Tamil Nadu, Karnataka, Telangana, Uttar Pradesh and West Bengal.

ZEELCHEM™ 7000 · Terpolymer

What is a terpolymer in water treatment?

A polymer made from three different monomers, typically carboxylic, sulphonic and nonionic. Together they give scale inhibition, calcium tolerance, phosphate/zinc stabilisation and dispersion in one product.

When do I need a terpolymer instead of a copolymer?

Use a terpolymer when the system has several problems at once, such as phosphate, zinc, iron and high pH, or when you want to run at high cycles of concentration.

Can ZEELCHEM™ 7000 be used in non-phosphorus programs?

Yes. Combined with PBTC and azoles, it forms the polymer core of all-organic, low-phosphorus cooling water programs.

What is the typical dose of terpolymer?

3–20 mg/L as product in recirculating water, or 1.5–2.5 mg/L product for every mg/L of orthophosphate in phosphate programs.

Is ZEELCHEM™ 7000 available pan-India?

Yes. It is dispatched from Vadodara to all Indian states in 65 kg HDPE carboys and 260 kg HDPE barrels.

ZEELCHEM™ 1000.S7 · Sodium Polyacrylate Liquid

What is sodium polyacrylate liquid used for?

It is used as a dispersant and scale inhibitor in water treatment, and as a deflocculant or dispersant for ceramics, CaCO₃/kaolin/pigment slurries, paper coating, paints and detergents.

What is the difference between ZEELCHEM™ 1000 and 1000.S7?

ZEELCHEM™ 1000 is acidic polyacrylic acid (pH 2–3). ZEELCHEM™ 1000.S7 is its neutralised sodium salt (pH 6–8), which is safer to handle and suits pH-sensitive processes.

Is this the same as super-absorbent sodium polyacrylate?

No. Super-absorbent polymer (SAP) is a cross-linked, very high molecular weight powder used in diapers. ZEELCHEM™ 1000.S7 is a low molecular weight, water-soluble liquid dispersant.

What dose is used as a ceramic deflocculant?

Typically 0.2–0.8 % on the weight of dry clay or body, optimised by viscosity (flow cup) tests.

Do you deliver sodium polyacrylate across India?

Yes. ZEELCHEM™ 1000.S7 ships from Vadodara to every state, including the ceramic clusters of Morbi, Thangadh and Khurja.

Need a polymer for your water system?

Share your water analysis and system details. Our technical team will recommend the right ZEELCHEM™ polymer and dosage, and send today's price with TDS, MSDS and COA.